ThinOX4PC comes in two different models:
- ThinOX4PC (T9050 model) designed to extend the life of your third-party PCs, notebooks or thin clients, turning them into powerful thin clients.
- ThinOX4PC USB (T9250) allows you to offer your staff the opportunity to work in a secure way even outside the company, from a ready-to-use live USB.
In both cases, the user experience is smooth and flawless and all the devices can be fully and automatically managed by Praim ThinMan.
¶ ThinOX4PC Models
The following table summarizes the characteristics of the models that are part of ThinOX4PC.
| S.O. | ThinOX | ThinOX |
| Hardware | any type of device In order to check hardware compatibility, it is necessary to create the ThinOX4PC live USB key version , you can use any type of USB (except Unsupported-usb-pen-drive-list)). Then, you can keep working with the created USB key or install ThinOX4PC on the device disk. |
It runs on a USB key created by Praim |
| License | The license is linked to a device. To activate the license, the device has to contact the ThinMan Server which will assign it a license (if there is at least one available on the server). In the case of ThinOX4PC as a Live USB Key, the license will be connected to the device in which the USB is inserted. Should it be necessary to change device, the ThinMan administrator can remove the device from the ThinMan Server so that new device can get the released license after its notification to ThinMan. |
The license is linked to the USB provided by Praim. The USB contains already the license which is validated everytime the device notifies to ThinMan Server The solution is fully mobile. It will work independently from the device where the USB is inserted(no limit for the number of devices where it can be connected) |
| Startup Behaviour | Boot the device from USB and choose:
|
|
| Versions Interoperability | Available from ThinOX version 10.1.12 Can be managed by ThinMan from version 7.6.2 |
Available from ThinOX version 11.4.2 Can be managed by ThinMan from version 8.1.0 |
How to point ThinMan from a device
For more information, read ThinMan Configuration on ThinOX and How to Setup ThinMan Address on Thin Client.
T9050 - Limitation of the Live version versus an installed ThinOX4PC
The ThinOX4PC LIVE does NOT mount the USB mass storage devices. So the Live version cannot be used to test the USB mass storage redirection to the virtual environment.
¶ System requirements and compatibility
¶ Minimum requirements
- RAM: 2Gb.
- Processor: 64bit and 2Ghz.
- HDD: 20Gb.
¶ Supported hardware
Currently supported devices
You can find here a complete list of currently supported hardware models that have been reported to date.
ThinOX4PC (and also the Live version) will support x86 processor type (not ARM).
Supported Ethernet Adapter:
- Intel
- Realtek
- Broadcom
- Qualcomm
Supported Graphics Card:
- AMD
- Intel
- NVIDIA GEFORCE 210. The VID:PID of the card should be 10de:0a65.
- VESA (is used as generic driver if the video card is not recognized)
Supported WiFi Adapter:
- Intel AC3160
- Intel N2200
- Unex DNXA-116
Support disks type:
- EIDE
- SATA
¶ Known limitation on hardware
In some cases, we found that hardware is not capable of performing expected work depending on software clients.
Here is the list of know limitation:
- PC based on Intel(R) Pentium(R) 4 CPU 2.40GHz is not capable of rendering the VMware client correctly using PCoIP protocol.
¶ Unsupported hardware or peripherals
Unsupported Wi-Fi Adapter:
- Ralink RT3290 802.11bgn Wi-Fi Adapter Unsupported USB pen Drive:
- For more details about usupported USB Pen Drive see the following link Praim Toolkit Compability Matrix - Unsupported USB pen drive list
¶ More about ThinOX4PC
ThinOX User Guide
See the generic ThinOX User Guide for all the capabilities available on a ThinOX device.
How-To
Check also the How-To section.
FAQ
Check also the Frequency Asked Questions section.